Spray Guns

High Pressure – Plural Component – Direct Impingement – Mechanical Purge

Pentech’s spray guns are extremely simple to operate, very compact, light weight, highly maneuverable, with the lowest parts count in the industry.

Follow a manual added link

MG Spray Gun

Download Manual
Follow a manual added link

BD Spray Gun

Download Manual
Follow a manual added link

Palm Gun

Download Manual
Follow a manual added link

Adapters &
Accessories

For the Spray Operator

  • Superior mix quality ensures you’re achieving the full potential of the coatings manufacturer’s material.
  • Simple to operate, lightweight and maneuverable.
  • Only requires three tools to operate(5/16” spin tight nut driver, 5/16” wrench, and a pin-vise).
  • Minimal parts count allows easy identification and rapid service.
  • 5 minutes to flush and clean at the end of the day.
  • No valving rod and PCD adjustment are necessary.
  • Extremely flexible 24″ whip hose assembly reduces operator fatigue and increases maneuverability.

For the Company

  • Our Spray Guns combine the features of multiple expensive guns into one versatile unit.
  • Lower entry cost and greatly reduced maintenance costs than our competitors.
  • Save money by greatly reducing coatings consumption due to precise placement of spray pattern.
  • Lower maintenance prices.
  • Greater ease of use and service reduces your downtime. This increased efficiency reduces job costs.
  • Eliminates the cost of replacing expensive electrically heated whip hoses, damaged by flexing, by using extremely flexible, short, and inexpensive whip hoses attached to the gun.
  • MG Gun
  • The compact lightweight maneuverable lowest parts count spray gun.
  • Introduced
  • Min Output
  • Max Output
  • Height
  • Width
  • Length
  • Weight
  • MG Gun
  • The compact lightweight maneuverable lowest parts count spray gun.
  • 2010
  • 1 lb/min (.4536 kg)
  • 23 lbs/min (10.43kg)
  • 6 ½” (16.51 cm)
  • 2″ (5.08 cm)
  • 2 ¾” (6.99 cm)
  • 1.9Lbs. (0.86kg)
  • BD Gun
  • The compact lightweight maneuverable lowest parts count spray gun
  • 2007
  • 1 lb/min (.4536 kg)
  • 40 lbs./min (18.14 kg)
  • 6 3/4″ (17.15 cm)
  • 2 5/8″ (6.67 cm)
  • 4 1/4″ (10.80 cm)
  • 2.5Lbs. (1.13 kg)
  • Palm Gun
  • Designed for the Navy, the Palm Gun has been replaced by the MG Spray Gun.
  • 2004
  • 1 lb/min (.4536 kg)
  • 6 lbs./min (2.7 kg)
  • 6″ (15.24 cm)
  • 2″ (5.08 cm)
  • 3 ½” (8.89 cm)
  • 2.5Lbs. (0.79 kg)

Features

  • Simple operation, easy set-up and maintenance
  • Versatile – Sprays Polyurea Coatings, Urethane, and Spray Foams
  • Inexpensive to service, industries lowest rebuild cost
  • Less than 5 minute clean up
  • Requires 3 minutes to change PCD
  • Will dispense materials at 1:1 through 4:1 ratios
  • Round Spray Pattern and Variable Flow rates.
  • Excellent Mix
  • Lowest Cost Mix Package (pattern control disc mix module)
  • Adapter blocks and fittings to connect to any make of proportioner
  • Coupling Block with material shut-off valves allows leakage free disconnect from gun
  • Extremely flexible 24” whip hose assembly
  • Valving Rod & PCD require no adjustment
  • Rebuild-able check valves

Applications

  • Shipboard / Offshore
  • Refinery / Pipe / Tank
  • Bridge / Architectural
  • Truck Bed Liners
  • Automotive Ground Effects
  • Secondary containment
  • In Mold Coatings, Scenic Theaming and Fabrication for the Theme & Prop Industry
  • Foam Insulation and Roofing
  • EPS hard-coating